Ice maker not making ice at all
We meter the board's valve output and the inlet valve together. If the board is not firing the valve, we repair or replace the board and confirm water flow before we leave.
Same-day control board diagnostics and repair across Forrest County
Ice Maker Control Board Repair Hattiesburg MS Done Right
Ice Maker Control Board Repair Hattiesburg MS is the fastest path back to a full ice bin. When your Whirlpool, KitchenAid, or Samsung board stops sending voltage to the mold, auger, or water inlet valve, we test it, repair it, or swap it on the first visit. We work refrigerators, undercounter units, and commercial machines across Hattiesburg, MS, so you are not waiting a week for ice.
Careful work. Honest options.
About this service
Ice Maker Control Board Repair Hattiesburg MS Explained
Ice Maker Control Board Repair Hattiesburg MS is the diagnostic and repair service that restores the low-voltage brain running your ice maker. That board reads the thermostat, fires the water inlet valve, cycles the mold heater, and tells the auger motor when to turn. When it fails, you get no ice, hollow cubes, or a machine that hums and does nothing. We pull the board, test every circuit with a multimeter, and repair the failed relay, capacitor, or solder joint instead of guessing at parts.
Hattiesburg summers push ice makers hard. A machine in a garage off Hardy Street Corridor runs at 95 degrees ambient and the board heat-soaks until a relay sticks. In older homes near the Hattiesburg Historic Neighborhood, voltage sags from aging wiring finish off weak boards early. If your ice maker control board is not working in Hattiesburg Mississippi, we carry OEM boards for Whirlpool, GE, LG, Frigidaire, Scotsman, and Manitowoc on the truck so most jobs finish in one trip.
- ✓ One-Visit Turnaround
- ✓ Repair, Not Guesswork
- ✓ OEM Boards Only
- ✓ Warranty on the Work
What's included
What Our Control Board Repair Covers
Every control board job includes full diagnostics, the repair or replacement itself, and a complete cycle test before we pack up. Here is what you get, and what we handle as an add-on only if your machine needs it.
✓
Full Board Diagnostics
We test incoming voltage, relay continuity, thermistor resistance, and output signals with a multimeter. You get a written explanation of what failed and why, not just a part number.
✓
Repair or OEM Replacement
Failed relays, capacitors, and solder joints get repaired in-house. Cracked or water-damaged boards get an OEM replacement matched to your model number, with the old part returned to you.
✓
Water Path Inspection
We check the water inlet valve, water line, and filter because a leaking or clogged line is a common cause of board failure. Fixing the cause prevents a repeat failure.
✓
Full Harvest Cycle Test
After the repair we run the machine through a complete cycle, watching fill, freeze, harvest, and auger operation. We do not leave until it produces a full batch of clear ice.
✓
90-Day Parts and Labor Warranty
The repair is covered for 90 days. If the same board fault returns in that window, we come back and make it right at no charge.
How it works
How Our Control Board Repair Works
01
Phone Diagnosis
Call 111 222 333 and describe the symptom. No ice, warm cubes, a blinking error code, or a machine that will not start all point to different faults. We ask for your brand and model, then book a window, usually the same day for Hattiesburg addresses.
02
On-Site Testing
Our tech arrives with a nut driver set, multimeter, and inspection mirror. We pull the board and check incoming voltage, relay continuity, and the thermistor circuit. This takes 20 to 30 minutes and tells us whether the board is truly dead or something upstream is starving it.
03
Repair or Replace
If a relay or solder joint failed, we repair the board and bench-test it. If the board is cracked or water-damaged, we install an OEM replacement matched to your model. Either way you get the old part back and a written breakdown of what failed.
04
Full Cycle Test
We reassemble, restore power, and run a complete harvest cycle. That means watching the water inlet valve fill, the mold heat, and the auger push cubes into the bin. We do not leave until the machine makes a full batch of clear ice.
05
Cleanup and Walkthrough
We wipe down the cabinet, check the condenser coils for dust, and show you what to watch for. If your water filter is past due, we flag it. You get the invoice, the warranty terms, and our number for follow-up questions.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Multimeter
Tests incoming voltage, relay continuity, and thermistor resistance on the control board before we condemn it.
Nut Driver Set
Opens refrigerator and undercounter cabinets cleanly so we can reach the board without damaging panels or wiring harnesses.
Inspection Mirror
Lets us see the back of the board and the cabinet interior for corrosion, water staining, and burnt traces.
Leak Detection Dye
Traces water line leaks that drip onto boards, so we fix the cause and not just the symptom.
Thermometer
Verifies mold and bin temperatures against the board's thermostat readings to confirm the circuit is calibrated.
Manifold Gauge Set
Checks sealed-system pressures when a board fault and a compressor fault look alike from the outside.
Refrigerant Recovery Machine
Recovers refrigerant to EPA Section 608 standards whenever a repair requires opening the sealed system.
Real results
Before and after.
KitchenAid Refrigerator, Oak Grove
Before
A homeowner in Oak Grove had a KitchenAid refrigerator that stopped making ice after a storm. Two other companies quoted a full unit replacement at over $1,800. The bin had been empty for nine days.
After
We metered the board, found a failed relay, and repaired it in 70 minutes. The machine produced a full bin of clear ice the same afternoon. Total cost was $285, including the diagnostic.
Manitowoc Commercial Unit, Hardy Street
Before
A bar on the Hardy Street Corridor lost its Manitowoc machine on a Friday night. The board showed no lights and the machine would not start. They were facing a weekend without ice.
After
We arrived Saturday at 9 a.m., confirmed the board had failed, and installed an OEM replacement by 11 a.m. The machine was running full cycles before the lunch rush. Cost was $520 parts and labor.
Samsung Unit, Kamper Park Area
Before
A homeowner near Kamper Park saw blinking error codes and hollow cubes for two weeks. The dispenser worked but the mold never filled properly, and ice quality kept dropping.
After
We traced the code to the mold heater relay, repaired the board, and replaced a clogged water filter. A full harvest cycle confirmed solid, clear cubes. Total was $310.
Problems we solve
Board Problems We Fix in Hattiesburg
Control board failures show up in a handful of ways, and each one points to a different circuit. We test before we replace so you pay for the right fix.
Ask a pro →↗
Ice maker dispensing warm or hollow ice
We test the board's heater relay and thermostat circuit. A stuck relay gets repaired on site, and we verify cube quality through a full harvest cycle.
Board failure after a water leak
We fix the water line leak first, dry and inspect the cabinet, then replace the corroded board. That order is why our board repairs last.
Blinking error codes and no cycle start
We read the code, trace it to the actual circuit, and confirm the fault with a multimeter. You get the real diagnosis, not a guess.
Proof you can check
Credentials and Reviews
✓
EPA Section 608 CertificationU.S. Environmental Protection Agency
✓
NATE CertificationNorth American Technician Excellence
✓
Manufacturer Service CertificationWhirlpool, KitchenAid, GE, and Samsung authorized training programs
✓
State Appliance Repair LicenseMississippi state licensing authority
✓
OSHA Safety ComplianceOccupational Safety and Health Administration
Most control board repairs in Hattiesburg run $180 to $450 in 2026, including the diagnostic. A straight board replacement with an OEM part lands at the higher end, usually $300 to $550 depending on brand. Commercial boards for Scotsman or Manitowoc machines cost more because the parts do. You get the range before we start work.
We do. Ice Maker Repair Experts handles board-level diagnostics and repair across Hattiesburg, Oak Grove, and Forrest County. We work on Whirlpool, KitchenAid, GE, Samsung, LG, Frigidaire, Scotsman, Manitowoc, Hoshizaki, Ice-O-Matic, U-Line, and Sub-Zero units. Call 111 222 333 and we will book a window, usually same day.
Yes, in most cases. We stock common boards and carry the tools to repair relays and solder joints on site. Call before noon and a same-day slot is realistic for Hattiesburg, Midtown, and the Hardy Street Corridor. If your exact board is not on the truck, we order it and return within 48 hours.
The common signs are no ice at all, hollow or small cubes, a machine that hums without cycling, blinking error codes, and an auger that will not turn. Sometimes the dispenser works but the mold never fills. Any of those point to the board or its inputs, and a multimeter test confirms which.
More services
Related Services
Ice Maker RepairGeneral ice maker repair covers the full machine, and control board faults are one of the most common reasons we get called. If your board tests fine, we move straight into the rest of the system.Explore →
Commercial Ice Maker RepairRestaurants and bars on Hardy Street Corridor run Manitowoc and Scotsman machines hard. Commercial board failures stop service fast, so we prioritize these calls and stock the boards those units use.Explore →
Residential Ice Maker RepairHome refrigerators from Whirlpool, GE, and Samsung make up most of our residential board work. We handle built-in, French-door, and side-by-side units across Hattiesburg neighborhoods.Explore →
Refrigerator Ice Maker RepairWhen the refrigerator ice maker quits, the board is a prime suspect. We test the board, the water inlet valve, and the thermostat together so you are not paying for the wrong part.Explore →
Freezer Ice Maker RepairFreezer-mounted ice makers run colder and their boards see more thermal cycling. That stress cracks solder joints over time, which is a repair we handle in-house.Explore →
Undercounter Ice Maker RepairUndercounter units from U-Line and Sub-Zero pack electronics into tight spaces where heat builds. Board replacement on these requires careful disassembly, and we do it daily.Explore →
Countertop Ice Maker RepairCountertop machines use smaller boards that fail from moisture and scale. We diagnose and replace those boards, then clean the water path so the new board lasts.Explore →
Ice Machine RepairIce machine repair covers the whole unit, from the compressor to the bin. Control board work is a core part of that service, especially on commercial machines that run around the clock.Explore → Ready when you are
Get Your Ice Maker Control Board Repair Hattiesburg MS Today
One call gets a certified tech to your door with the tools and boards to finish the job. We test first, repair or replace second, and leave with your machine making ice. Call 111 222 333 now.
Book Same-Day Repair 111 222 333 →
Request an appointment
Contact Our Hattiesburg Ice Maker Techs
Call 111 222 333 or email info@icemakerrepairexperts.com and we will get you on the schedule. We answer the phone during business hours and return after-hours messages first thing the next morning. Most Hattiesburg calls placed before noon are handled the same day.
Call anytime111 222 333Email the officeinfo@icemakerrepairexperts.us
Office hoursOpen 24 hours · 7 days a week