Ice maker not making ice at all
We test the valve, thermostat, and board with a multimeter, then replace the failed part or the whole unit. Most Hattiesburg no-ice calls are a bad water inlet valve, and we carry those on the truck.
Same-day ice maker swap out across Forrest County
Ice Maker Replacement Hattiesburg MS Done Right the First Time
When your ice maker quits, you need Ice Maker Replacement Hattiesburg MS fast. We swap out failed Whirlpool, KitchenAid, GE, Samsung, and LG units across Forrest County, usually the same day you call. Our techs carry the tools, parts, and refrigerant handling gear to finish most jobs in one visit. You get cold ice again without waiting a week for a callback.
Careful work. Honest options.
About this service
Ice Maker Replacement Hattiesburg MS: What the Job Really Involves
Ice Maker Replacement Hattiesburg MS means pulling the failed unit out of your fridge or stand-alone machine and fitting a new one that actually matches your model. That covers the ice maker mold, water inlet valve, control board, and water line. We test the fill cycle, check the thermostat, and confirm the auger turns free before we call it done. Most swaps take two to four hours from arrival to first batch of ice.
Hattiesburg water runs hard, and that mineral load eats ice makers faster than most homeowners expect. We see scaled-up molds, clogged water filters, and cracked inlet valves all over the Hardy Street Corridor and West Hattiesburg. If you are searching for ice maker replacement in Hattiesburg MS near me, we cover 39401, 39402, and 39406 daily. A failed compressor or control board usually means replacement beats repair.
- ✓ Ice in Hours, Not Weeks
- ✓ Lower Water Bills
- ✓ Cleaner Ice, Every Batch
- ✓ Warranty-Backed Parts
What's included
What Our Ice Maker Replacement Covers
Every replacement includes the parts and labor to get you making ice again, plus the checks that catch the next failure before it happens. Here is what is in the standard job.
✓
New Ice Maker Assembly
We supply and install a new mold and head unit matched to your fridge or machine model. That covers Whirlpool, KitchenAid, GE, Samsung, LG, Frigidaire, and the common commercial brands.
✓
Water Inlet Valve Check
We test the valve with a multimeter and replace it if it is sticking or leaking. A bad valve is the number one cause of no-ice calls in Hattiesburg, so we do not skip it.
✓
Water Line Flush
The old line gets flushed and inspected for cracks or kinks. If it is brittle or leaking, we replace it and pressure-test the new connection before we close up.
✓
Bin and Line Sanitizing
We pull the bin, scrub it, and sanitize everything that touches your ice. That kills the slime and mold that builds up in humid Mississippi kitchens.
✓
Two-Cycle Test Run
We run two full harvest cycles and watch the cubes drop. That confirms the fill level, thermostat, and auger are all working before we call the job done.
How it works
Our Ice Maker Swap Out Process
01
Phone Diagnosis
You call and describe the symptom: no ice, warm ice, leaking water, or a jammed auger. We ask for your brand and model, then quote a range on the spot. If it sounds like a control board or compressor failure, we tell you before we roll so there are no surprises.
02
On-Site Testing
Our tech meters the water inlet valve, checks the thermostat, and reads the control board for error codes. We pull the unit and inspect the mold, auger, and water line for scale or cracks. This takes 20 to 30 minutes and tells us whether replacement is the right call.
03
Parts Match
We match the new ice maker to your exact model, whether that is a Scotsman undercounter unit or a Samsung French door fridge. If the water filter or inlet valve is due, we swap those too. Most trucks carry the common assemblies for Hattiesburg-area brands.
04
Install and Seal
We set the new mold, reconnect the water line, and torque the flare fittings so nothing drips. The bin gets sanitized and the line gets flushed. Then we run two full harvest cycles and watch the cubes drop to confirm the fill level and thermostat are dialed in.
05
Test and Walkthrough
Before we leave, we show you the first batch, check for leaks under the cabinet, and set your filter reminder. You get the old part if you want it, plus a plain-English rundown of what failed. Total time on site runs two to four hours.
Tools & methods
Tools and Methods We Use on Every Job
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Multimeter
Tests the water inlet valve, thermostat, and control board for continuity and voltage. It tells us which part failed instead of guessing.
Manifold Gauge Set
Reads high and low side pressures on sealed systems so we can diagnose compressor and refrigerant issues accurately.
Vacuum Pump and Recovery Machine
Pulls a deep vacuum and recovers refrigerant under EPA Section 608 rules before any sealed-system repair.
Tube Cutter and Flare Tool
Cuts and flares copper and plastic water lines cleanly so the new fittings seal without leaks.
Nut Driver Set and Inspection Mirror
Gets into tight fridge cabinets and lets us see behind the unit for leaks, cracks, and scale we would otherwise miss.
Leak Detection Dye and Thermometer
Confirms hidden water leaks and verifies the ice maker is cycling at the right temperature after the swap.
Real results
Before and after.
Samsung Fridge Back to Clear Ice
Before
A West Hattiesburg family was buying two bags of ice a week. The Samsung ice maker had a cracked inlet valve, a scaled mold, and a clogged filter. The bin smelled and cubes came out cloudy and small.
After
We replaced the mold and valve, swapped the filter, and sanitized the bin and line. Two harvest cycles later the unit was dropping clear cubes. They stopped buying bagged ice and cut about $30 a month off the grocery bill.
Manitowoc Restaurant Machine Back Online
Before
A Hardy Street bar lost its Manitowoc machine on a Friday. The control board had failed and the condenser coils were packed with dust. They were looking at a weekend of bagged ice and lost drink sales.
After
We replaced the control board, cleaned the condenser, and verified ice output against AHAM standards. The machine was back to full production before the dinner rush. That saved the weekend.
Oak Grove Leak Stopped, Floor Saved
Before
An Oak Grove homeowner found water under the fridge and a warped cabinet base. The water line had cracked and the inlet valve would not close. The ice maker had been leaking roughly 15 gallons a day.
After
We replaced the water line and valve, swapped the ice maker, and pressure-tested the new connection. The floor dried out and the cabinet base was saved. The water bill dropped noticeably the next month.
Problems we solve
Ice Maker Problems We Fix in Hattiesburg
Most ice maker failures fall into a handful of patterns. Here is what we see most and how we handle it.
Ask a pro →↗
Ice maker leaking water onto the floor
We trace the leak with dye and an inspection mirror, then fix the source. Usually it is a cracked water line or a valve that will not close. We replace the part and pressure-test before we leave.
Small or hollow ice cubes
We check the water filter, inlet valve, and thermostat. A new filter and a fill-level adjustment fix most cases. If the mold is scaled up, we replace it and sanitize the bin.
Ice maker mold and slime buildup
We pull the unit, scrub and sanitize the bin and line, and replace the mold when it is pitted. A fresh water filter keeps it clean longer in Hattiesburg's hard water.
Proof you can check
Licensed, Certified, and Local
✓
EPA Section 608 CertificationU.S. Environmental Protection Agency
✓
NATE CertificationNorth American Technician Excellence
✓
Manufacturer Service CertificationMajor ice maker and appliance brands
✓
State Appliance Repair LicenseMississippi state licensing authority
✓
OSHA Safety ComplianceOccupational Safety and Health Administration
Most replacements run $280 to $650 installed, depending on the brand and whether the water inlet valve or filter needs swapping too. Undercounter and commercial units like Scotsman or Manitowoc can run higher. We quote a range on the phone and confirm it before we start. Typical 2026 pricing in this area has stayed steady on common Whirlpool and GE assemblies.
We do, across all of Forrest County. Our techs handle refrigerator, freezer, undercounter, and countertop ice makers for homes and businesses. If you are in Oak Grove, Midtown, or the Hardy Street Corridor, we are usually there the same day. Call and we will confirm a window before we head out.
Often yes. We keep same-day slots open for ice maker failures, and our trucks carry the common molds and valves. Call before noon and we can usually be there by late afternoon. If your model needs a specialty part, we will tell you the lead time upfront instead of leaving you guessing.
Plan on two to four hours on site. The swap itself is about 90 minutes, then we run two harvest cycles and check for leaks. If we are also replacing the water line or filter, add 30 minutes. You will have ice dropping before we leave, and we walk you through the first batch.
More services
Other Ice Maker Services We Handle in Hattiesburg
Ice Maker RepairNot every failure needs a full swap. We diagnose the water inlet valve, thermostat, and control board first, and repair when the mold and auger are still sound. Many Hattiesburg jobs end here for a fraction of replacement cost.Explore →
Commercial Ice Maker RepairRestaurants and bars on Hardy Street run Manitowoc, Hoshizaki, and Ice-O-Matic machines hard. We service those units and replace failed components fast so you are not buying bagged ice during a dinner rush.Explore →
Residential Ice Maker RepairFridge ice makers in Hattiesburg homes take a beating from hard water. We repair and replace the molds, valves, and boards in Whirlpool, GE, Samsung, and LG units, usually in one visit.Explore →
Refrigerator Ice Maker RepairIf your fridge makes no ice or dispenses warm cubes, the issue is often the inlet valve or control board. We test both and replace the ice maker when the mold is scaled beyond cleaning.Explore →
Freezer Ice Maker RepairFreezer-mounted ice makers freeze up and jam the auger. We thaw, inspect, and replace the unit when the mold is cracked or the thermostat has drifted out of range.Explore →
Undercounter Ice Maker RepairU-Line and Scotsman undercounter units in Hattiesburg kitchens and bars need clean condenser coils to make ice. We repair and replace these when airflow or the compressor is the problem.Explore →
Countertop Ice Maker RepairPortable countertop units clog with scale fast in this water. We clean, descale, and replace failed pumps and molds so your countertop machine keeps dropping cubes.Explore →
Ice Machine RepairStand-alone ice machines in Hattiesburg shops and offices get the same treatment: diagnosis, repair, or full replacement with a properly sized unit for your daily ice volume.Explore → Ready when you are
Get Your Ice Maker Replacement Hattiesburg MS Today
One call gets a licensed tech to your door with the parts to finish the job. We quote upfront, show up when we say, and leave you with ice. Call now and we will find you a same-day slot.
Book My Replacement 111 222 333 →
Request an appointment
Contact Our Hattiesburg Ice Maker Techs
Call 111 222 333 or email info@icemakerrepairexperts.com and we will get you on the schedule. We answer the phone during business hours and return after-hours messages first thing the next morning. Most Hattiesburg calls placed before noon are handled the same day.
Call anytime111 222 333Email the officeinfo@icemakerrepairexperts.us
Office hoursOpen 24 hours · 7 days a week