Residential Ice Maker Repair in Hattiesburg gets your fridge making clean, clear ice again, usually the same day you call. We work on Whirlpool, KitchenAid, GE, Samsung, LG and Frigidaire units in Downtown, Oak Grove and West Hattiesburg. If your home ice maker repair Hattiesburg MS job has been sitting on the to-do list, we can diagnose the water inlet valve, mold or control board and have ice dropping before dinner.
Residential Ice Maker Repair in Hattiesburg is the diagnosis and repair of the ice-making system inside your household refrigerator or freestanding ice machine. We test the water inlet valve, ice maker mold, thermostat, auger and control board, then trace the fault with a multimeter and manifold gauge set. Most failures come down to a clogged water filter, a stuck valve, a cracked water line or a control board that quit reading temperature. We confirm the actual cause before we quote parts, so you are not paying to replace something that still works.
Hattiesburg water runs hard, and that mineral load coats valves and molds faster than most homeowners expect. Add our long, humid summers and a fridge working overtime, and ice makers here fail sooner than the same unit would up north. We see it constantly in older homes around the Historic Neighborhood and in rentals near the Hardy Street Corridor. If you are searching for ice maker repair for homes near me Hattiesburg, we cover Forrest County seven days a week with same-day home ice maker repair Hattiesburg MS appointments.
Every residential ice maker repair visit covers a full diagnostic and the repair itself. We test the whole ice-making system, not just the part you called about, because a failing thermostat often hides behind a valve symptom. Parts are quoted separately at flat rates, and you approve the price before we start.
We test the water inlet valve, ice maker mold, thermostat, auger, control board and water line with a multimeter and thermometer. This 20 to 30 minute diagnostic finds the real fault instead of guessing at the loudest symptom.
Hattiesburg hard water leaves scale in the line and valve. We flush the line, check flow pressure, and clear any mineral buildup. This step alone restores ice production on a lot of calls and prevents the next failure.
We install OEM valves, thermostats, augers, control boards, filters and gaskets for Whirlpool, GE, Samsung, LG, KitchenAid and Frigidaire. Generic parts fail early on hard water, so we stick with manufacturer parts.
After the repair we run three full harvest cycles and check cube size, clarity and bin temperature. You watch ice drop before we leave. If the dispenser or auger sticks, we catch it right there in your kitchen.
We wipe down the work area, haul off old parts, and walk you through what failed and how to keep it running. You get a short list of habits, like filter timing, that protect the repair.
You describe the symptom, we narrow the likely cause. Not making ice, leaking water, warm cubes or a jammed auger each point to a different part. Two minutes on the phone tells us which parts to load, and we book a same-day window that fits your schedule.
We pull the unit, inspect the water inlet valve, ice maker mold and water line, then meter the thermostat and control board. A manifold gauge set and thermometer confirm whether the compressor and refrigerant charge are healthy. This takes 20 to 30 minutes and tells us the real fault.
Before any repair starts you get the diagnosis in plain English and a flat price for parts and labor. If the fix is not worth it, we say so and credit the diagnostic toward a replacement quote. No pressure, no upsell on parts your unit does not need.
We replace the failed valve, mold, thermostat or control board, clear any auger jam, and flush the water line. Filters and gaskets get swapped while we are in there. Most repairs run 45 to 90 minutes, and we clean up the kitchen before we leave.
We run three harvest cycles, check cube size and clarity, and confirm the dispenser works. You get a walkthrough of what failed and a short list of habits that keep it running. Our work is warrantied, and we note the parts used on your invoice.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Tests continuity and voltage on thermostats, water inlet valves and control boards. It tells us whether a part has actually failed or the board is not sending power.
Reads refrigerant pressures on the sealed system. We use it to confirm compressor health before quoting a repair that touches the refrigeration circuit.
Required for sealed-system work. We recover refrigerant under EPA Section 608 rules and pull a proper vacuum before recharging.
Cuts and flares copper line cleanly when we replace a water line or repair a fitting. Clean flares prevent the leaks that ruin cabinet floors.
Gets into tight fridge compartments and lets us see behind the unit where leaks and mold hide. Most water line failures are invisible without a mirror.
Dye finds slow leaks we cannot see, and the thermometer confirms bin and mold temperatures during the harvest-cycle test.
A Samsung French-door fridge in Oak Grove stopped making ice in July. The bin was empty, the display showed no error, and the family was buying bagged ice every few days. The water filter had not been changed in over a year.
We found a scaled-up water inlet valve and a clogged filter. Replaced both with OEM parts, flushed the line, and ran three harvest cycles. Cube production returned to normal within two hours, and bin temperature held at 5 degrees Fahrenheit.
A Whirlpool unit near Kamper Park was dripping onto the kitchen floor. The homeowner noticed a musty smell and a soft spot near the cabinet base. The water line behind the fridge had a hairline crack at the fitting.
We replaced the water line and compression fitting, dried the area, and sanitized the bin where mold had started. A 24-hour dry-test showed no drips. The cabinet floor was saved before it needed replacement.
A GE side-by-side in West Hattiesburg would not dispense ice. The bin was full but the auger would not turn, and the motor was straining. The homeowner had been forcing the dispenser, risking motor burnout.
We cleared the auger jam, inspected the drive motor, and replaced a worn auger coupling. Dispensing worked cleanly on the first test. We also corrected the cube size setting, which was producing oversized cubes that jammed.
Most Hattiesburg ice maker calls fall into a handful of patterns. Here is what we see, what it costs you if you wait, and how we fix it.
Ask a pro →We test the water inlet valve, thermostat and control board with a multimeter, isolate the failed part, and replace it with an OEM component. Most no-ice calls trace back to a stuck valve or a clogged filter, and both are same-day fixes.
We trace the leak with leak detection dye and an inspection mirror, checking the water line, valve and drain. We replace the failed part, dry-test the repair, and confirm no drips before we leave your kitchen.
This is almost always a clogged water filter or a scaled-up valve on Hattiesburg water. We replace the filter, flush the line, and test flow pressure. Cube size and clarity come back the same day.
We pull the mold and bin, scrub and sanitize with food-safe cleaner, and flush the water line. We also check the filter and drain, because standing water is what feeds the growth in the first place.
Most residential ice maker repairs in Hattiesburg run $150 to $450 in 2026, including the diagnostic. A simple water inlet valve or thermostat swap sits near the low end. A control board, compressor or sealed-system repair pushes toward the top. We give you the flat price before we start, so the number you hear is the number you pay.
We do. Ice Maker Repair Experts handles household ice maker repair Hattiesburg calls across Forrest County, including Downtown, Midtown, Oak Grove and West Hattiesburg. We service Whirlpool, KitchenAid, GE, Samsung, LG, Frigidaire and freestanding brands like Scotsman and Manitowoc. Call 111 222 333 and we will book a same-day window.
Yes. Built-in refrigerator ice makers are our most common job. We repair the mold, auger, thermostat, water inlet valve, dispenser and control board inside Whirlpool, GE, Samsung, LG and Frigidaire fridges. We also handle the water line and filter feeding the unit, which is where a lot of Hattiesburg hard-water failures start.
We do, and it is the reason most customers call us. Book before noon and we can usually be in your kitchen the same afternoon with the parts on the van. For emergency residential ice maker repair in Hattiesburg Mississippi, call 111 222 333 and we will tell you honestly what is available today.
Ice Maker RepairGeneral ice maker repair covers the same parts we touch on residential calls, from water inlet valves to control boards. If your unit is not a standard household fridge model, this is the service to book. We diagnose the fault first, then quote the fix.Explore →
Commercial Ice Maker RepairRestaurants and bars around the Hardy Street Corridor run Scotsman, Manitowoc, Hoshizaki and Ice-O-Matic machines. When a commercial unit goes down, we apply the same diagnostic discipline we use on home ice makers, with priority scheduling so your service does not stop.Explore →
Refrigerator Ice Maker RepairThis is the core of what we do for Hattiesburg homeowners. We repair the ice maker built into your Whirlpool, GE, Samsung, LG or Frigidaire fridge, including the mold, auger, thermostat and dispenser. Most fridge ice maker failures trace back to water flow or a control board.Explore →
Freezer Ice Maker RepairFreezer-mounted ice makers freeze up differently than in-door units. We clear ice blockages, test the thermostat, and check the water inlet valve feeding the mold. If your freezer ice maker stopped mid-cycle, this is the service that gets it harvesting again.Explore →
Undercounter Ice Maker RepairUndercounter units from U-Line and Sub-Zero are common in Hattiesburg wet bars and outdoor kitchens. They need condenser coil cleaning more often in our humid climate. We repair the compressor, water line and control board and clean the coils while we are there.Explore →
Countertop Ice Maker RepairPortable countertop ice makers clog with scale fast on Hattiesburg water. We descale the mold, replace the water filter, and test the pump and thermostat. If your countertop unit makes small or hollow cubes, this is usually a scale or flow problem we can fix on site.Explore →
Ice Machine RepairFreestanding ice machines get the same treatment as built-in units: full diagnostic, parts replacement, and a harvest-cycle test before we leave. We stock valves, thermostats and control boards for the brands Hattiesburg homes and small businesses run most.Explore →
Ice Maker InstallationNew ice maker going in? We handle the water line, shutoff valve, filter and drain connection so the unit is set up to code. Proper installation prevents the leaks and low-flow problems that cause most early ice maker failures in Hattiesburg homes.Explore →Ice on the floor or an empty bin? Call 111 222 333 and we will book a same-day window for your home. Flat pricing, OEM parts, and warrantied work across Forrest County. We test every repair before we leave, so you see ice drop before we pack up.
Book Same-Day Repair 111 222 333 →Call 111 222 333 or email info@icemakerrepairexperts.com and we will get you on the schedule. We answer the phone during business hours and return after-hours messages first thing the next morning. Most Hattiesburg calls placed before noon are handled the same day.