Ice Maker Leak Repair Hattiesburg MS is what you call when the ice maker starts dripping across the kitchen floor. We fix Whirlpool, GE, Samsung, LG and Scotsman units across Forrest County, usually the same day you call. Our techs carry a multimeter, manifold gauge set and leak detection dye on every truck, so most leaks get found and sealed in one visit. You get a dry floor, a working ice maker and upfront pricing before we start.
Ice Maker Leak Repair Hattiesburg MS is the trade of finding where water escapes an ice maker and sealing it at the source. Water can leave through a cracked water inlet valve, a split water line, a failed ice maker mold, a clogged drain, or a worn door gasket. We pull the unit, inspect the line and valve with an inspection mirror, then test the repair under pressure before we slide the machine back. Most residential jobs take two to four hours, and commercial machines run a bit longer because of the ice bin and condenser work involved.
In Hattiesburg, ice maker leaks show up year-round, but the worst calls come in late summer when humidity hits the high 80s and a slow drip turns into a wet cabinet floor overnight. Rentals near the Hardy Street Corridor and older homes in the Hattiesburg Historic Neighborhood tend to have brittle saddle valves and copper lines that have been tapped one too many times. If you search for an ice maker leak repair near me Hattiesburg, you want a tech who has seen that exact setup before. We have, and we carry the parts to fix it on the first trip.
Every Ice Maker Leak Repair Hattiesburg MS visit starts with a full leak diagnosis and ends with a pressure test. The core repair is included in the quoted price. If we find a second problem while we are in there, we tell you the cost before we touch it, and you decide whether to fix it now or later.
We pull the unit, shut the supply and inspect the valve, line, mold and drain with an inspection mirror. Leak detection dye and a multimeter confirm the source. This is the step that keeps us from replacing parts that are still good.
The inlet valve is the most common leak point on Whirlpool, GE, Samsung and LG units. We replace the solenoid valve, test the coil and check the fitting for a proper seal. Most valve jobs take under an hour.
Cracked copper and brittle plastic lines get cut out and replaced with a new line, flared to fit. We pressure test before closing up. This is the fix that holds when a saddle valve has been tapped one too many times.
A clogged drain or a worn door gasket can mimic a valve leak. We clear the drain, check the gasket seal and replace it if it is letting warm air in. Small part, big effect on overflow.
We run a full fill and freeze cycle with the line pressurized and watch for 15 to 20 minutes. If a drop appears, we stay until it is gone. You do not pay for a repair we have not verified.
We dry the cabinet and floor, then leave you a note on what failed, what we replaced and what to watch. You also get the workmanship warranty terms in writing. No mystery about what happened.
We ask what you are seeing: water under the fridge, ice that tastes off, a machine that stopped mid-cycle. That five-minute call tells us whether to bring a water inlet valve, a control board or a full water line kit. You get a two-hour arrival window and a call when the tech is on the way.
The tech pulls the unit, shuts the supply valve and inspects the line, valve, mold and drain with an inspection mirror. A multimeter checks the valve solenoid, and leak detection dye confirms the path water is taking. This step runs 20 to 40 minutes and tells us exactly what to fix.
We replace the failed part, whether that is a water inlet valve, a section of water line, a door gasket or a cracked ice maker mold. Lines get cut with a tube cutter and re-flared, not patched with tape. Most repairs take one to two hours once the diagnosis is done.
Before we call it fixed, we run the machine through a full fill and freeze cycle with the line pressurized. We watch the valve, the line and the drain for 15 to 20 minutes. If a drop shows up, we stay until it is gone. No leak leaves the driveway until we see it dry.
We wipe down the cabinet, dry the floor and show you what failed and why. You get the part name, the warranty terms and two or three things to watch for. If a water filter was due, we note it so the next leak does not start there.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Tests the water inlet valve solenoid and control board voltage so we replace the failed part, not a working one. It is the first tool out of the bag on most leak calls.
Reads system pressures on compressor and refrigerant jobs. We use it to confirm the charge is correct after any sealed-system repair under EPA Section 608 rules.
Pulls a deep vacuum before recharging a system. Skipping this step leaves moisture in the lines and shortens compressor life, so we never skip it.
Recovers refrigerant legally before any sealed-system work. Required by EPA Section 608 and standard practice on every compressor or condenser repair we run.
Cuts and re-flares water lines for a clean, leak-free connection. A proper flare is the difference between a repair that holds and one that drips again in a month.
Lets us see behind the fridge and under the ice bin without pulling the whole unit apart. Most hidden leaks are found with this and a flashlight.
Confirms the exact path of a slow leak that is hard to see. We add it to the water path, run a cycle and check with a UV light.
A homeowner in Oak Grove had water pooling under a Samsung French-door fridge for three days. Towels were not keeping up, and the cabinet base was starting to swell. The water line had cracked at the compression fitting behind the unit.
We replaced the cracked line, re-flared the fitting and pressure tested for 20 minutes. The floor dried within a day and the cabinet base stopped swelling. Total job time was about 90 minutes, and the ice maker was back to full production by evening.
A restaurant on the Hardy Street Corridor was losing ice quality because water was dripping into the bin from a failed inlet valve. The bin had visible slime buildup, and staff were dumping ice twice a shift.
We replaced the water inlet valve, cleaned the condenser and sanitized the bin and lines. The machine held a full cycle with no drip. Ice quality came back to normal, and the staff stopped dumping ice mid-shift.
A landlord in the Hattiesburg Historic Neighborhood had a tenant reporting water under the fridge for over a week. The original saddle valve had finally failed at the seal, and the cabinet floor was damp and musty.
We replaced the saddle valve with a proper shutoff, installed a new water line and tested the repair under pressure. The cabinet dried out over two days, and the tenant stopped calling. We sent the landlord before and after photos for the file.
Most ice maker leaks fall into a handful of categories. Knowing which one you have saves time and money. Here are the problems we solve most often on Ice Maker Leak Repair Hattiesburg MS calls.
Ask a pro →We trace the puddle to its source, usually a failed water inlet valve or a cracked line. The valve or line gets replaced, the fitting gets tested under pressure, and we dry the area before leaving. Most of these jobs finish in under two hours.
Call us and we shut the supply valve first, then diagnose. We keep emergency slots for active leaks, so we can usually be there the same day. Once the source is fixed, we run a full cycle to confirm the floor stays dry.
We defrost the fill tube, replace the cracked mold or worn gasket causing the drip, and verify the freeze cycle with a thermometer. This is common on older Frigidaire and Whirlpool units in Hattiesburg rentals.
We service Manitowoc, Hoshizaki and Ice-O-Matic machines on site, replace the inlet valve or drain part, and sanitize the bin. Priority scheduling keeps your service day intact. Most commercial leak calls are handled in one visit.
Most residential ice maker leak repairs in Hattiesburg run $180 to $450 in 2026, including the diagnostic and the part. A simple water inlet valve swap sits at the low end. Water line replacement, control board work or commercial machine repairs push toward the top. Emergency and after-hours calls add a trip fee. You get the number before we start, so there is no surprise on the invoice.
We do. Ice Maker Repair Experts handles ice maker leak repair across Hattiesburg, Forrest County and the surrounding areas, including Oak Grove, West Hattiesburg and the Hardy Street Corridor. Our techs carry the tools and common parts to diagnose and fix most leaks in one visit. Call 111 222 333 and we will give you an arrival window.
Yes, in most cases. We hold same-day slots six days a week and keep emergency openings for active leaks. Call before noon and there is a strong chance we are at your door the same afternoon. If we are booked out, we tell you honestly and schedule the earliest window, usually the next morning.
The four most common causes we find are a failed water inlet valve, a cracked or loose water line, a clogged drain, and a worn door gasket letting warm air in and causing overflow. Hard water in this area also scales up valves faster than most people expect. A 20-minute diagnosis with dye and a multimeter tells us which one you have.
Ice Maker RepairWhen the leak is fixed but the machine still will not make ice, our Ice Maker Repair service covers the auger, mold, thermostat and control board. Hattiesburg customers often book both in one visit so the unit leaves working, not just dry.Explore →
Commercial Ice Maker RepairRestaurants and bars on Hardy Street run Manitowoc, Hoshizaki and Ice-O-Matic machines hard. Commercial Ice Maker Repair handles high-volume leaks, condenser cleaning and refrigerant work under EPA Section 608 rules, with priority scheduling so you do not lose a service day.Explore →
Residential Ice Maker RepairHome refrigerators from Whirlpool, GE, Samsung and LG make up most of our residential calls. Residential Ice Maker Repair covers the fridge-mounted units in kitchens across Hattiesburg, including the water line and valve work that stops most leaks.Explore →
Refrigerator Ice Maker RepairIf your leak is inside the fridge cabinet, Refrigerator Ice Maker Repair is the right call. We pull the unit, inspect the fill tube and mold, and replace what failed. Most Hattiesburg fridge ice maker leaks trace back to a $30 valve or a cracked fill tube.Explore →
Freezer Ice Maker RepairFreezer-mounted ice makers leak when the fill tube ices over or the mold cracks. Freezer Ice Maker Repair covers defrost drain clogs, mold replacement and thermostat checks. We see this most in older Hattiesburg homes where the freezer has run for a decade or more.Explore →
Undercounter Ice Maker RepairU-Line and Sub-Zero undercounter units leak at the inlet valve or the drain pump. Undercounter Ice Maker Repair handles tight cabinet access, which is common in Midtown Hattiesburg kitchens and bar areas. We bring the right tools for confined spaces.Explore →
Countertop Ice Maker RepairCountertop units leak at the reservoir seal or the drain plug. Countertop Ice Maker Repair covers those small machines, plus descaling when mineral buildup causes overflow. Quick jobs, usually under an hour, and worth it before water reaches the counter seam.Explore →
Ice Machine RepairStandalone ice machines need the same leak work as fridge units, plus bin and drain attention. Ice Machine Repair covers the full machine, from water inlet valve to ice bin. We service the machines behind Hattiesburg restaurants, clinics and offices.Explore →Water under the fridge does not fix itself, and every hour it sits, the damage spreads into the cabinet and subfloor. We are licensed, insured and stocked with the parts that stop most leaks in one visit. Call now and we will give you a same-day window.
Book a Repair 111 222 333 →Call 111 222 333 or email info@icemakerrepairexperts.com and we will get you on the schedule. We answer the phone during business hours and return after-hours messages first thing the next morning. Most Hattiesburg calls placed before noon are handled the same day.