Ice maker not making ice at all
We test the valve, thermostat, and water line in sequence. Once we find the failed part, we replace it on the spot. Most no-ice calls finish in under two hours, and you see ice drop before we leave.
Same-day ice maker parts repair for homes and businesses across Forrest County
Ice Maker Parts Replacement Hattiesburg MS You Can Count On
When your ice maker quits, you need Ice Maker Parts Replacement Hattiesburg MS fast. We stock water inlet valves, control boards, thermostats, and augers for Whirlpool, KitchenAid, GE, Samsung, and LG units, so most repairs finish in one visit. Whether it is a refrigerator ice maker in Oak Grove or a Manitowoc machine at a Hardy Street restaurant, we diagnose the fault, replace the failed part, and test the cycle before we leave. Call 111 222 333 and we will get your ice bin full again.
Careful work. Honest options.
About this service
Ice Maker Parts Replacement Hattiesburg MS Explained
Ice Maker Parts Replacement Hattiesburg MS is the appliance repair service that swaps out failed components inside your ice maker so the machine freezes, harvests, and dispenses ice again. We replace water inlet valves, ice maker molds, augers, thermostats, control boards, water filters, and water lines. A multimeter and manifold gauge set tell us whether the fault is electrical or refrigerant-related before we quote. Most jobs take 60 to 120 minutes, and we carry common parts for Whirlpool, GE, Samsung, LG, Frigidaire, Scotsman, and Manitowoc on the truck.
Hattiesburg summers push ice makers hard, and the humidity around Kamper Park and the Bouie Street Area accelerates mold and slime buildup in the bin and water line. When your ice maker stops making ice, leaks water, or dispenses warm cubes, the cause is usually one failed part, not the whole unit. We see this constantly in homes built before 1980 near Downtown Hattiesburg, where original water lines have scaled shut. If you have been searching for ice maker parts replacement in Hattiesburg MS near me, we can be at your door the same day.
- ✓ Parts On The Truck
- ✓ Same-Day Service
- ✓ 90-Day Parts Warranty
- ✓ Upfront Flat Pricing
What's included
What Our Ice Maker Parts Replacement Covers
Every job includes a full diagnostic, the replacement part, installation, and a cycle test. We tell you upfront what is covered and what is not, so there are no surprises on the invoice.
✓
Full Diagnostic Testing
We test the water inlet valve, thermostat, control board, and compressor with a multimeter and manifold gauge set. The diagnostic pinpoints the failed part and tells us whether the fix is electrical, mechanical, or refrigerant-related.
✓
OEM Or Equivalent Part
We install OEM parts whenever possible and high-quality equivalents when OEM is not available. Every part we install carries a 90-day warranty covering both the component and our labor.
✓
Water Line And Filter Check
We inspect the water line for leaks, kinks, and scale, and check the water filter. If the filter is clogged, we replace it so the new part gets clean, full-pressure water from day one.
✓
Full Cycle Test
Before we leave, we run the ice maker through a complete freeze-and-harvest cycle. You watch ice drop into the bin. We also check for leaks with an inspection mirror and confirm the machine holds temperature.
✓
Cleanup And Haul-Away
We clean up after ourselves and haul away the failed part. Your kitchen or back-of-house looks the way it did before we arrived, minus the broken ice maker part.
How it works
How Our Ice Maker Parts Replacement Works
01
Phone Diagnosis
You call 111 222 333 and describe what the ice maker is doing, or not doing. We ask about the brand, model, and symptoms like leaking water or warm cubes. Two minutes on the phone usually tells us which parts to load, so the technician arrives prepared.
02
On-Site Testing
The technician tests the water inlet valve, thermostat, and control board with a multimeter, then checks refrigerant pressure with a manifold gauge set if the compressor is suspect. This takes 20 to 30 minutes and pinpoints the failed part before any work begins.
03
Flat Quote
We show you the failed component, explain what it does, and give you one flat price for the replacement. You approve it or you do not. No pressure, no hidden fees, and no charge for the diagnosis if you move forward with the repair.
04
Part Replacement
We pull the old valve, board, thermostat, or auger and install the new one using a nut driver set and flare tool. Water lines get a tube cutter and fresh compression fittings. Most replacements take 45 to 90 minutes depending on access.
05
Cycle Test
Before we pack up, we run the ice maker through a full freeze-and-harvest cycle and check for leaks with an inspection mirror. You see ice drop into the bin before we leave. If anything is off, we fix it on the spot.
Tools & methods
Tools And Methods We Use Every Day
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Multimeter
Tests voltage and continuity on the water inlet valve, thermostat, and control board. It tells us which component has failed before we replace anything.
Manifold Gauge Set
Reads refrigerant pressure on the compressor and sealed system. We use it to confirm whether a warm-ice complaint is a thermostat issue or a refrigerant problem.
Refrigerant Recovery Machine
Recovers refrigerant safely when a compressor or sealed-system component needs replacement. We follow EPA Section 608 rules on every recovery.
Tube Cutter And Flare Tool
Cuts and flares copper water lines cleanly when we replace a leaking line or install a new inlet valve. Clean flares prevent future leaks.
Nut Driver Set
Removes the screws and hex-head fasteners on ice maker molds, augers, and control boards without stripping them. Essential for tight access inside refrigerators.
Inspection Mirror And Leak Detection Dye
Finds hidden leaks behind the ice maker and under the bin. The dye shows slow leaks that are invisible to the naked eye.
Thermometer
Verifies the freeze cycle reaches the correct temperature. We check the mold and bin temperature after every repair to confirm the machine is working.
Real results
Before and after.
KitchenAid Refrigerator Ice Maker In Oak Grove
Before
A family in Oak Grove had a KitchenAid refrigerator ice maker that stopped producing ice. The machine ran but nothing dropped into the bin. They had been buying bagged ice for two weeks.
After
We tested the water inlet valve and found it had failed. We replaced it with an OEM valve in 45 minutes and ran a full cycle test. Ice was dropping before we left. Total cost: $240, including the part and labor.
Manitowoc Commercial Machine In Downtown Hattiesburg
Before
A Downtown Hattiesburg restaurant had a Manitowoc ice machine that quit on a Thursday afternoon. The control board was flashing an error code and the machine would not cycle. They faced a weekend without ice.
After
We arrived within three hours, diagnosed a failed control board, and replaced it with a Manitowoc OEM board. The machine ran through five cycles before we left. The restaurant opened Friday with full ice production. Cost: $620.
U-Line Undercounter Ice Maker In The Avenues
Before
A homeowner in The Avenues had a U-Line undercounter ice maker leaking water onto hardwood floors. The leak was slow and had already damaged the cabinet base. The ice also tasted bad.
After
We pulled the unit, found a cracked water line and a clogged filter, and replaced both. We also cleaned and sanitized the bin, which had mold from Hattiesburg humidity. No leaks after a 24-hour dry test. Cost: $310.
Problems we solve
Ice Maker Problems We Solve In Hattiesburg
Most ice maker failures trace back to one worn component. We find it, replace it, and get your ice production back to normal, usually in a single visit.
Ask a pro →↗
Ice maker leaking water onto the floor
We trace the leak with an inspection mirror and leak detection dye, checking the inlet valve, water line, and drain. We replace the failed part, dry-test the repair, and confirm no drips remain.
Ice maker producing small or hollow ice
We check the water filter, water line, and inlet valve. A clogged filter or weak valve is the usual culprit. We replace the part, restore full water flow, and verify cube size on the next cycle.
Ice maker mold and slime buildup
We disassemble the ice path, clean and sanitize every surface, and flush the water line. We also replace the water filter and show you a simple monthly cleaning routine to keep it clear.
Proof you can check
Licensed, Certified, And Warrantied
✓
EPA Section 608 CertificationU.S. Environmental Protection Agency
✓
NATE CertificationNorth American Technician Excellence
✓
Manufacturer Service CertificationWhirlpool, KitchenAid, GE, Samsung, LG, Scotsman, Manitowoc, Hoshizaki, Ice-O-Matic, U-Line, Sub-Zero
✓
State Appliance Repair LicenseMississippi state licensing authority
✓
OSHA Safety ComplianceOccupational Safety and Health Administration
Most residential jobs run $180 to $450 in 2026, including the part and labor. A water inlet valve or thermostat sits at the low end near $180. A control board or compressor replacement pushes toward $450 or more. Commercial machines like Manitowoc or Scotsman units can run $300 to $850 depending on the component.
We do. Ice Maker Repair Experts is a local Hattiesburg shop serving Forrest County and all 39401, 39402, and 39406 ZIP codes. We carry parts for Whirlpool, KitchenAid, GE, Samsung, LG, Frigidaire, Scotsman, Manitowoc, Hoshizaki, Ice-O-Matic, U-Line, and Sub-Zero, and we handle both residential and commercial ice makers.
Yes, in most cases. Call before 2 p.m. and we will have a technician at your door the same day with the parts your model needs. We stock water inlet valves, thermostats, control boards, and augers on the truck, so roughly 8 out of 10 same-day ice maker parts repair Hattiesburg MS calls finish in one visit.
You can order online and wait a week, or you can call us and have the right part installed today. We stock OEM and high-quality aftermarket components for all major brands at our Hattiesburg location. We do not sell parts over the counter, but we install them, and every part carries a 90-day warranty.
More services
Other Ice Maker Services We Handle In Hattiesburg
Ice Maker RepairWhen your ice maker stops making ice, leaks water, or dispenses warm cubes, our repair service diagnoses the fault and fixes it. We handle electrical, mechanical, and refrigerant issues on all major brands, with same-day availability across Hattiesburg.Explore →
Commercial Ice Maker RepairRestaurants, bars, and hotels in Downtown Hattiesburg depend on us when a Manitowoc, Scotsman, or Hoshizaki machine goes down. We stock commercial-grade parts and offer emergency service so you do not lose a weekend of sales.Explore →
Residential Ice Maker RepairFrom refrigerator ice makers in Oak Grove to undercounter units in The Avenues, we repair residential ice makers fast. We carry common parts for Whirlpool, GE, Samsung, and LG, so most homes get fixed in a single visit.Explore →
Refrigerator Ice Maker RepairYour fridge ice maker quits for a handful of reasons: a bad water inlet valve, a failed thermostat, or a cracked water line. We test each component and replace only what failed, usually within two hours of arrival.Explore →
Freezer Ice Maker RepairFreezer ice makers deal with the coldest temperatures in the appliance, which wears out thermostats and molds faster. We replace those parts and check the water line for ice blockages that stop production.Explore →Undercounter Ice Maker RepairUndercounter units in Hattiesburg kitchens and wet bars need compact parts and careful access. We work on U-Line, Sub-Zero, and Ice-O-Matic models and keep the most common components in stock.Explore →
Countertop Ice Maker RepairPortable countertop ice makers clog with scale and slime faster than built-in units. We clean the system, replace the water filter, and swap failed pumps or control boards so your machine runs clear again.Explore →
Ice Machine RepairWe service freestanding ice machines for restaurants, convenience stores, and offices across Forrest County. From compressor failures to condenser coil cleaning, we keep commercial ice production running.Explore → Ready when you are
Get Ice Maker Parts Replacement Hattiesburg MS Today
Your ice maker quit, and you need it back. Call 111 222 333 and we will diagnose the fault, quote a flat price, and replace the failed part, often the same day. Every repair carries a 90-day parts warranty.
Book Same-Day Service 111 222 333 →
Request an appointment
Contact Our Hattiesburg Ice Maker Techs
Call 111 222 333 or email info@icemakerrepairexperts.com and we will get you on the schedule. We answer the phone during business hours and return after-hours messages first thing the next morning. Most Hattiesburg calls placed before noon are handled the same day.
Call anytime111 222 333Email the officeinfo@icemakerrepairexperts.us
Office hoursOpen 24 hours · 7 days a week