Ice maker not making ice at all
We test the coil and line pressure, replace the failed valve, and confirm the mold fills on the next cycle. Most Hattiesburg homes have ice again within 24 hours.
Fast valve fixes for Whirlpool, GE, Samsung, LG and Scotsman machines
Ice Maker Valve Repair Hattiesburg MS Done Right
Ice Maker Valve Repair Hattiesburg MS gets your ice flowing again when a failed water inlet valve leaves the bin empty or the floor wet. We test the coil, check line pressure, and replace the valve with an OEM-matched part. Most homes in Forrest County get same-day service, and we carry the common Whirlpool, GE, Samsung and LG valves on the truck so you are not waiting on a special order.
Careful work. Honest options.
About this service
Ice Maker Valve Repair Hattiesburg MS Explained
Ice Maker Valve Repair Hattiesburg MS is the appliance service that diagnoses and replaces the water inlet valve controlling flow into your ice maker. That small solenoid valve opens on a signal from the control board, fills the mold to a precise level, then closes. When the coil weakens or mineral scale jams the diaphragm, you get no ice, slow ice, or water running down the back of the fridge. We test the coil with a multimeter, check incoming line pressure, and confirm the mold fill before we replace anything.
Hattiesburg water carries enough calcium that inlet valves scale up faster than most homeowners expect, especially on homes off older galvanized service lines near Downtown and The Avenues. A failing valve often shows up as ice maker leaking water or an ice maker not making ice, and it can flood a kitchen floor overnight. If you need ice maker valve repair in Hattiesburg Mississippi, we stock valves for Whirlpool, KitchenAid, GE, Samsung, LG, Frigidaire, Scotsman, Manitowoc, Hoshizaki, Ice-O-Matic, U-Line and Sub-Zero so the job usually finishes in one visit.
- ✓ Stop Water Damage
- ✓ Ice Back Same Day
- ✓ Protect the Mold and Auger
- ✓ Lower Water Bills
What's included
What Our Valve Repair Includes
Every Ice Maker Valve Repair Hattiesburg MS call includes a full diagnostic, the replacement valve, and a leak test before we leave. If the real fault turns out to be the control board, thermostat, or water line, we tell you and quote that instead of replacing a good valve.
✓
Full Valve Diagnostic
We test the solenoid coil with a multimeter, check line pressure, and inspect the diaphragm for scale or cracks. This tells us whether the valve is actually the fault before we touch it.
✓
OEM-Matched Replacement Valve
We install a valve matched to your Whirlpool, GE, Samsung, LG, Frigidaire, Scotsman or Manitowoc machine. No generic parts that fail in six months and leave you calling again.
✓
Water Line and Saddle Valve Check
We inspect the supply line and saddle valve while we are in there. If the line is brittle or the saddle valve is weeping, we fix it now instead of waiting for it to fail.
✓
Fill Volume and Leak Test
We run two full fill cycles and confirm the mold fills to spec. An inspection mirror and dye check catch any drip before we button the fridge back up.
✓
Old Part and Walkthrough
You get the failed valve and a plain-English explanation of what went wrong. We also give you tips to slow scale buildup so the next valve lasts longer.
How it works
How Our Valve Repair Process Works
01
Phone Diagnosis
You call and describe the symptom: no ice, slow ice, or water under the fridge. We ask the brand and model, then book a window, usually same-day. Most calls in Hattiesburg and Oak Grove get a two-hour arrival window.
02
On-Site Testing
The tech pulls the fridge, shuts the water, and tests the inlet valve coil with a multimeter. We check line pressure, inspect the water line and saddle valve, and look for scale or cracks. This takes about 20 minutes.
03
Valve Replacement
We cut the water line with a tube cutter, swap the failed valve for an OEM-matched unit, and reseat every connection. A flare tool and nut driver set keep the fittings tight. The swap itself runs 30 to 45 minutes.
04
Leak and Fill Test
We restore water, run two full fill cycles, and watch for drips with an inspection mirror. We confirm the mold fills to the right level and the ice maker cycles normally. Nothing gets buttoned up until it passes.
05
Cleanup and Walkthrough
We wipe down the area, push the fridge back, and walk you through what failed and why. You get the old part, a warranty on the valve, and tips to keep the next one lasting longer.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Multimeter
Tests the inlet valve solenoid coil for continuity and confirms whether the coil has burned out or is still good.
Tube Cutter and Flare Tool
Cuts the water line clean and forms a proper flare so the new valve connection seals without a drip.
Nut Driver Set
Opens the fridge or machine panels without stripping screws, so the job stays clean and reversible.
Inspection Mirror and Leak Detection Dye
Finds slow drips behind the fridge and confirms the new valve and line are dry before we leave.
Manifold Gauge Set and Vacuum Pump
Diagnoses the sealed system when a valve tests good but the machine still runs warm or short-cycles.
Refrigerant Recovery Machine
Handles refrigerant safely under EPA Section 608 rules whenever a repair touches the sealed circuit.
Thermometer
Checks bin and mold temperatures so we know the ice maker is cycling in the right range after the valve swap.
Real results
Before and after.
Oak Grove Whirlpool Leak Fixed
Before
A Whirlpool side-by-side in Oak Grove had been dripping behind the fridge for days. The homeowner noticed a warped floorboard and an empty ice bin. The inlet valve coil tested open and the diaphragm was coated in scale.
After
We replaced the valve with an OEM-matched Whirlpool part, cleared the scale from the fill tube, and pressure-tested the line. The floor stayed dry and the bin was full within 18 hours. Total job time was about 75 minutes.
Downtown Restaurant Back Online
Before
A Manitowoc machine at a Downtown Hattiesburg restaurant quit on a Friday afternoon. The bin was empty and the dinner rush was two hours away. The inlet valve had failed and the supply line was kinked behind the unit.
After
We swapped the commercial valve, straightened and re-clamped the line, and ran two fill cycles. Ice production was back before the rush. The owner avoided a weekend of buying bagged ice at roughly $3 a bag.
The Avenues Slow Fill Solved
Before
A homeowner in The Avenues complained of hollow cubes and a half-empty bin on a Samsung fridge. The valve coil tested good, but line pressure at the valve was low because of a clogged filter and a long, partly kinked water line.
After
We replaced the water filter, rerouted the line, and installed a new valve as a precaution. Fill volume came back to spec and the cubes were solid again within a day. The fix cost far less than a new ice maker.
Problems we solve
Problems We Solve With Valve Repair
Most no-ice and water-on-the-floor calls in Hattiesburg trace back to the inlet valve. Here are the specific problems we fix every week.
Ask a pro →↗
Ice maker leaking water on the floor
We shut the supply, replace the valve, and pressure-test the line. We also check the saddle valve and water line so the leak is fully closed, not just slowed.
Ice maker producing small or hollow ice
We measure fill volume, replace the valve, and clear any scale in the fill tube. Cubes come out full and solid again.
Ice maker dispensing warm ice
We test the valve first, then check the compressor and condenser coils with a manifold gauge set if the valve is good. You get the right diagnosis, not a guess.
Proof you can check
Licensed, Certified, Warrantied
✓
NATE CertificationNorth American Technician Excellence
✓
Manufacturer Service CertificationMajor ice maker and refrigerator brands
✓
EPA Section 608 CertificationU.S. Environmental Protection Agency
✓
State Appliance Repair LicenseMississippi state licensing authority
Most valve repairs in Hattiesburg run $180 to $420 in 2026, including the part and labor. A standard residential inlet valve is usually $40 to $120, and labor runs $120 to $250 depending on access. Commercial machines like Manitowoc or Hoshizaki can run higher because the valves are heavier and the panels take longer to open.
We do. Ice Maker Repair Experts handles ice maker valve repair in Hattiesburg MS and the surrounding Forrest County area, including Oak Grove, West Hattiesburg and the Hardy Street Corridor. We carry the common Whirlpool, GE, Samsung, LG and Frigidaire valves on the truck, so most jobs finish the same day you call.
Yes, in most cases. Call before noon and we can usually get a tech out the same day. We stock the top 20 residential inlet valves, so if yours is a common model we finish in one visit. If it is a rare commercial valve, we will tell you the lead time upfront before you commit.
The three most common causes we see are a burned-out solenoid coil, mineral scale jamming the diaphragm, and a clogged or kinked water line. Hattiesburg water is hard enough that scale builds up faster than in softer-water cities. A multimeter test on the coil and a pressure check on the line tells us which one you have in about 20 minutes.
More services
Related Services
Ice Maker RepairGeneral ice maker repair covers the whole machine, from the mold to the auger. When a valve is only one of several faults, we bundle the work so you pay one trip charge instead of two.Explore →
Commercial Ice Maker RepairRestaurants and bars around Downtown Hattiesburg run Manitowoc, Hoshizaki and Ice-O-Matic machines. Their inlet valves are heavier-duty and often feed a reverse-osmosis line, so we test both the valve and the supply.Explore →
Residential Ice Maker RepairHome refrigerators from Whirlpool, GE, Samsung and LG make up most of our valve calls. We handle the fridge-side valve, the saddle valve, and the water line in one visit.Explore →
Refrigerator Ice Maker RepairWhen the fridge ice maker stops, the inlet valve is the first thing we test. If the valve is fine, we move to the control board and thermostat before quoting any part.Explore →
Freezer Ice Maker RepairFreezer-mounted ice makers freeze the fill tube if the valve drips. We replace the valve and clear the frozen tube so the mold fills correctly again.Explore →
Undercounter Ice Maker RepairU-Line and Sub-Zero undercounter units have tight valve access. We pull the unit, swap the valve, and pressure-test the line before sliding it back under the counter.Explore →
Countertop Ice Maker RepairCountertop units use small solenoid valves that scale up fast. We replace them and descale the reservoir so the machine runs a full cycle without stalling.Explore →
Ice Machine RepairStandalone ice machines share the same valve design as refrigerators. We test the coil, check line pressure, and replace the valve with an OEM-matched part.Explore → Ready when you are
Book Ice Maker Valve Repair Hattiesburg MS Today
Water on the floor or an empty bin? Call now and we will get a tech out, usually the same day. Every valve we install carries a 12-month parts warranty and a 90-day labor warranty.
Book Service 111 222 333 →
Request an appointment
Contact Our Hattiesburg Ice Maker Techs
Call 111 222 333 or email info@icemakerrepairexperts.com and we will get you on the schedule. We answer the phone during business hours and return after-hours messages first thing the next morning. Most Hattiesburg calls placed before noon are handled the same day.
Call anytime111 222 333Email the officeinfo@icemakerrepairexperts.us
Office hoursOpen 24 hours · 7 days a week