Slow drip behind the refrigerator
We trace the drip to the fitting or line, replace the failed section, and pressure-test it. Most slow-drip calls are a loose compression nut or a cracked saddle valve, and both are same-day fixes.
Same-day leak fixes for fridge, freezer and undercounter ice makers
Ice Maker Water Line Repair Hattiesburg MS
Ice Maker Water Line Repair Hattiesburg MS is what we do every day: we trace the leak, replace the failed water line or inlet valve, and pressure-test the run before we leave. If your ice maker water line fix in Hattiesburg MS has been put off because of a slow drip behind the fridge, we handle it in one visit. We work on Whirlpool, GE, Samsung, LG and Scotsman units across Forrest County, and we carry the common fittings on the truck.
Careful work. Honest options.
About this service
Ice Maker Water Line Repair Hattiesburg MS
Ice Maker Water Line Repair Hattiesburg MS is the repair of the small-diameter supply line, saddle valve, or water inlet valve that feeds your ice maker. The line runs from a household supply pipe to the back of the unit, usually through a saddle valve or shutoff, and it fails in predictable ways: pinhole pinholes in copper, cracked poly tubing, mineral-clogged valves, or a loose compression nut that drips a cup of water a day onto your floor. We cut out the bad section, install a new line, and confirm flow at the fill cup before we close up.
In Hattiesburg, the call usually comes after a slow leak has already warped a cabinet base or stained a wood floor. Older homes in the Historic Neighborhood and The Avenues often still have original copper runs, and our hard water leaves scale inside the inlet valve until it sticks open. That is when you see ice maker water line leaking Hattiesburg Mississippi symptoms: a puddle under the fridge, low ice production, or a water filter that clogs every few weeks. We fix the line and the valve together so you are not calling us back in a month.
- ✓ Same-Day Line Repair
- ✓ Leak Found, Not Guessed
- ✓ Hard-Water Valve Fix
- ✓ Floor and Cabinet Saved
What's included
What Our Water Line Repair Includes
Every ice maker water line repair job covers the full water path from the supply shutoff to the fill cup. If we find a related failure while we are in there, we quote it before we touch it, so you never get a surprise line item after the fact.
✓
Full Leak Trace
We pressurize the run and inspect the saddle valve, compression fittings, line and inlet valve with a mirror and leak detection dye. You get the exact failure point, not a guess.
✓
New Line and Fittings
Damaged copper or poly gets cut out and replaced with new 1/4-inch line and fresh compression fittings. We match the material to your setup so the repair lasts.
✓
Inlet Valve Check
We test the water inlet valve for scale and sticking, and replace it when needed. A valve that hangs open is the number one cause of repeat line leaks.
✓
Pressure Test
Three fill cycles and a 15-minute pressure watch before we leave. If the line weeps, we catch it on site and redo the connection at no extra charge.
✓
Shutoff Walkthrough
We show you where the saddle valve or shutoff is and how to close it, so a future leak is a five-second fix instead of a flooded floor.
✓
Cleanup
Cabinet floor dried, unit pushed back and leveled, old parts left with you. We treat your kitchen like it is ours.
How it works
How Our Water Line Repair Process Works
01
Phone Diagnosis
You call 111 222 333 and describe what you see: puddle, low ice, or no fill at all. We ask the unit brand and where the line enters the wall, then book a same-day window. The call takes about five minutes and costs nothing.
02
On-Site Leak Trace
The technician pulls the unit out, inspects the supply line with a mirror, and pressurizes the run to find the failure. We check the saddle valve, compression fittings, and the water inlet valve. This step runs 20 to 30 minutes.
03
Upfront Price
You get one flat price covering the line, fittings, and labor before any work starts. If the inlet valve or filter also needs replacing, it is added to the same quote. No hourly surprises, no trip charge added at the end.
04
Repair and Test
We cut out the damaged section, install new line, and set the valve. Then we run three fill cycles and watch the line under pressure for 15 minutes. If it drips, we redo it on the spot. Most repairs take 90 minutes to two hours.
05
Cleanup and Walkthrough
We dry the cabinet floor, push the unit back, and make ice with you watching. You get the old parts, a 12-month workmanship warranty, and a quick lesson on the shutoff valve location so you can kill the water fast next time.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Inspection mirror and leak detection dye
Lets us see behind the fridge and confirm the exact leak point without pulling cabinets apart.
Tube cutter and flare tool
Clean cuts and correct flares on copper line so the new connection seals the first time.
Nut driver set
Removes and reseats inlet valve and line fittings without stripping the hardware on Whirlpool, GE and Samsung units.
Manifold gauge set and vacuum pump
Used when a line repair reveals a sealed-system fault, so we can diagnose refrigerant-side problems on the same visit.
Refrigerant recovery machine
EPA Section 608 compliant recovery when compressor or sealed-system work is needed alongside the line repair.
Thermometer and multimeter
Verifies fill-cup temperature and tests the inlet valve circuit and control board signals.
Real results
Before and after.
Oak Grove Fridge Line Replacement
Before
A Samsung French-door fridge dripped about a cup of water a day onto a wood floor. The poly line had hardened and split at the saddle valve, and the cabinet base was starting to stain.
After
We replaced the line with braided stainless, installed a new shutoff valve, and pressure-tested the run for 15 minutes. The floor dried out, the stain stopped spreading, and the unit has filled on schedule for months.
The Avenues Copper Pinhole Fix
Before
A 1960s home had original copper line feeding a KitchenAid ice maker. A pinhole leak had soaked the cabinet floor and the ice had started tasting metallic.
After
We cut out the pitted copper, ran new line with fresh compression fittings, and replaced the scaled inlet valve. Fill pressure came back to spec and the metallic taste disappeared within two batches of ice.
Hardy Street Restaurant Emergency
Before
A Manitowoc ice machine stopped filling mid-Friday service. The inlet valve was scaled shut and the supply line was restricted, so the bin was empty by 6 p.m.
After
We replaced the valve and line from truck stock, ran three fill cycles, and had the machine producing ice before dinner service. No weekend shutdown and no emergency parts order.
Problems we solve
Water Line Problems We Fix Fast
Most ice maker water line failures look different on the surface but trace back to a handful of causes. Here is what we run into across Hattiesburg.
Ask a pro →↗
Ice maker not filling at all
We test the line, valve and filter in order, because a clogged filter or scaled valve is the cheapest cause. If the line is restricted, we replace it and restore fill pressure.
Hard-water scale in the inlet valve
We replace the water inlet valve and flush the line. Hattiesburg water is hard enough that valves here often fail in two to three years, so we check it on every line job.
Frozen or split line after a cold snap
We thaw, inspect and replace the line with freeze-resistant braided stainless, then test the run. If the line runs through a garage or exterior wall, we insulate it while we are there.
Proof you can check
Licensed, Certified, Reviewed
✓
State appliance repair licenseMississippi state licensing authority
✓
Manufacturer service certificationWhirlpool, KitchenAid, GE, Samsung, LG and Frigidaire authorized training programs
✓
NATE certificationNorth American Technician Excellence
✓
EPA Section 608 certificationU.S. Environmental Protection Agency
✓
OSHA safety complianceOccupational Safety and Health Administration
Most repairs run $180 to $450 in 2026, including parts and labor. A simple compression fitting swap sits at the low end; a full copper line replacement through a cabinet wall or a job that also needs a new water inlet valve lands at the high end. You get the exact price on site before we start, and there is no trip charge on scheduled work.
We do, across Forrest County and every Hattiesburg ZIP code, including 39401, 39402 and 39406. Our technicians carry a state appliance repair license and manufacturer service certification on the major refrigerator brands. Call 111 222 333 with your unit brand and we will book a same-day window, usually within a few hours.
Yes. Same-day ice maker water line fix Hattiesburg MS appointments are standard when you call before mid-afternoon. We keep line, fittings and inlet valves on the truck, so the repair usually finishes in one visit. If the leak is flooding a floor right now, shut the saddle valve and tell us it is an emergency when you call.
Three causes cover most of what we see: hard water scale cracking a copper line or jamming the inlet valve open, a loose or worn compression fitting at the saddle valve, and poly tubing that has hardened and split behind the fridge. We pressure-test the run, find which one it is, and replace the failed part rather than patching it.
More services
Related Services
Ice Maker RepairWhen the line is fine but the unit still will not make ice, we move into full ice maker repair: fill cup, mold, thermostat and control board checks. Most Hattiesburg line jobs include a quick function test so you know the whole circuit works.Explore →
Commercial Ice Maker RepairRestaurants and bars on Hardy Street run Manitowoc, Hoshizaki and Ice-O-Matic machines on the same kind of supply line. We repair commercial water lines and valves on a schedule that keeps your ice bin full through service.Explore →
Residential Ice Maker RepairHome refrigerators in Oak Grove and West Hattiesburg are our bread and butter. Residential ice maker repair covers the line, valve, filter and fill circuit on Whirlpool, GE, Samsung and LG units, usually in one visit.Explore →
Refrigerator Ice Maker RepairA fridge ice maker that stops filling is often a water line problem, not a fridge problem. We diagnose the line and the refrigerator ice maker together so you are not paying twice for the same diagnosis.Explore →
Freezer Ice Maker RepairStandalone freezers and garage units freeze their own supply lines in a cold snap. We thaw, inspect and replace the line with freeze-resistant braided stainless so the next front does not take your ice maker out.Explore →
Undercounter Ice Maker RepairU-Line and Sub-Zero undercounter units hide their water line behind a cabinet panel. We pull the unit, repair the line and valve, and reset it level so the door seals and the fill stays consistent.Explore →
Countertop Ice Maker RepairCountertop units use a small reservoir and pump instead of a household line, but they still leak at the inlet. We repair the fill assembly and check the pump so your counter stays dry.Explore →
Ice Machine RepairFreestanding ice machines share the same supply-line failure points as built-in units. We handle line repair, valve replacement and leak tracing on Scotsman, Manitowoc and Hoshizaki machines across Hattiesburg.Explore → Ready when you are
Book Ice Maker Water Line Repair Hattiesburg MS Today
A dripping line gets worse, not better. Call 111 222 333 and we will book a same-day window, give you a flat price on site, and back the work with a 12-month warranty. Licensed, insured and local to Forrest County.
Book Same-Day Repair 111 222 333 →
Request an appointment
Contact Our Hattiesburg Ice Maker Techs
Call 111 222 333 or email info@icemakerrepairexperts.com and we will get you on the schedule. We answer the phone during business hours and return after-hours messages first thing the next morning. Most Hattiesburg calls placed before noon are handled the same day.
Call anytime111 222 333Email the officeinfo@icemakerrepairexperts.us
Office hoursOpen 24 hours · 7 days a week